Rerunning or Resetting Windows Media Center Software Setup
___________________________________________________
This document pertains to HP and Compaq computers that came with Windows Media Center (2004 through Windows Vista Premium editions).
Depending on which Media Center version your computer is using, use one of the following sections to reconfigure the initial Media Center setup:
Rerunning the Setup Wizard in Windows Media Center for Vista Systems
Rerunning the Setup Wizard in Media Center 2005 Edition
Rerunning the Setup Wizard in Media Center Original and 2004
If your computer has Media Center Edition 2005, or Media Center Edition 2004, and the steps in this document do not work, you can also try Resetting the original Media Center Setup settings .
Rerunning the Setup Wizard in Windows Media Center for Vista Systems
This procedure allows you to change your existing Windows Media Center settings:
Click Start in the taskbar and then click Windows Media Center.
Scroll to Tasks, and then select settings.
Click General, and then click Windows Media Center Setup.
Click Run Setup Again.
Follow the onscreen instructions to change settings in the Windows Media Center Setup Wizard.
Rerunning the Setup Wizard in Media Center 2005 Editions
This procedure allows you to change your existing Media Center settings:
Click Start in the taskbar and then click Media Center.
Click Settings, General, and then click Media Center Setup.
Click Run Media Center Setup Again.
Follow the onscreen instructions to change settings in the Media Center Setup Wizard.
Rerunning the Setup Wizard in Media Center Original and 2004 Editions
This procedure allows you to change your existing Media Center settings:
Click Start and then Run.
Type the following into the Open field exactly as it appears:
c:\windows\ehome\ehshell.exe /homepage:fr.welcome.xml /pushstartpage:true
A Setup Wizard window appears.
Follow the onscreen instructions to change the Media Center software settings.
Resetting the original Media Center Setup Wizard settings
This procedure s used for troubleshooting and resets all Media Center settings in Media Center 2005 and earlier to allow Media Center Setup Wizard to start from the beginning and create new setup files.
CAUTION: The following procedure deletes all previous Media Center setup settings
CAUTION: The following procedure involves editing the Windows registry. Incorrectly editing the registry could cause Windows to not start. Create a backup of the registry before carefully following the steps.
Close Media Center.
Open My Computer. Click Start and then My Computer.
Make sure you can view hidden files, system files, and file extensions.
In the My Computer window, click the Tools menu and then select Folder Options.
Select the View tab.
Under Files and Folders place a check mark in the check box next to Display the contents of the system folders.
Under Hidden files and folders, select Show hidden files and folders.
Remove check mark from the check box next to Hide extensions for known file types.
Click OK.
Double-click the C: drive.
Double-click Documents and Settings, and then double-click All Users.
Double-click Application Data, double-click Microsoft, and then double-click eHome.
Right-click the ehshell.config file, and then click Delete. Close the eHome window.
Click Start, click Run, type
regedit into the Open text box, and then click OK.
Click the plus sign next to each item in the following path:HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Media Center
In the Media Center folder, right-click Settings, and then click Delete.
Click the plus sign next to each item in the following path:HKEY_LOCAL_MACHINES\Software\Microsoft\Windows\Current Version\Media Center
In the Media Center folder, right-click Settings, and then click Delete.
Open Media Center. Click Start on the taskbar, and then click Media Center to open and rerun the Media Center 2005 setup wizard.
Follow the onscreen instructions to set up the HP Media Center software.
Sunday, December 16, 2007
Playback and Picture Quality is Poor When Viewing TV and DVD Movies
Playback and Picture Quality is Poor When Viewing TV and DVD Movies
___________________________________________________
In this document:
Video playback pauses briefly (stutters) and the sound is not synchronized
Step 2: Turning off or customizing the power management settings
My TV display is black and white
A white or gray line appears on the screen
This document applies to HP Media Center computers using Microsoft Windows XP Media Center Edition.
Use the solutions listed below to resolve poor picture quality problems on Media Center computers.
Before you begin, make sure that the problem is not with the DVD movie, video file, or TV signal itself. If possible, make sure the DVD disc and video file can be played on another system and there is no problem with the TV signal.
Video playback pauses briefly (stutters) and the sound is not synchronized
Most playback problems can be resolved by updating the video and sound driver and freeing up the system resources.
Step 1: Updating the video and sound drivers
Playback software driver:
Media Center and Windows Media Player - Get the latest updates for Media Center and Windows Media Player using Windows Update . Updates contain the latest fixes and feature enhancements.
InterVideo WinDVD - To download the latest versions of WinDVD included with the HP Media Center computer go to HP Software and Driver Download Web Page . To upgrade to a full version of WinDVD or for updates use InterVideo's Web Site (in English).
TV tuner card driver - Go to the HP Software and Driver Download Web Page , enter the model name of the HP Media Center computer and download the latest TV tuner driver.
Graphics card driver - Go to the HP Software and Driver Download Web Page , enter the model name of your HP Media Center computer and download the latest graphics card driver.
Sound card driver - Go to HP Software and Driver Download Web Page , enter the model name of the HP Media Center computer, and download the latest graphics card driver.
Step 2: Turning off or customizing the power management settings
For more information about setting power management options, go to Power Management Overview (Windows XP) . To turn off or customize your power managment options, follow the steps below:
Open the Control Panel. Click Start on the taskbar, and then click Control Panel.
Click Performance and Maintenance and then click Power Options to open the Power Options Properties window.
Click the drop-down arrows to select your power managment options.
Click Apply, and then click OK to save your settings.
Step 3: Freeing up system resources
The computer system has limited resources. Running other programs while playing movies will use up these resources and may affect the picture quality. Use the following HP support document for details on how to make the computer run quicker and more efficient: Increasing System Resources Without Adding Memory
My TV display is black and white
Reinstall the TV tuner driver.
Restart the computer. Do not open any software programs, especially the Media Center software program. If you have any programs that start up automatically make sure you close them.
Click Start, All Programs, PC Help and Tools (or hewlett-packard, hp pavilion PC Tools, and then HP Application Recovery.
Select Driver Installation, and click Next.
Select the name of the TV tuner used on the computer (eMuzed or Hauppauge or Conexant).
Click Install, and then click OK after the driver has finished installing.
Click Quit to close the HP Application Recovery program and restart the computer.
Connect to the Internet and click Start, All Programs, and then Windows Update.
Install a new tuner driver from the list of driver updates. Select the name of the TV tuner that came with your computer and install the new driver.
Restart the computer.
A white or gray line appears on the screen
If your PC model includes a GeForce 6600 graphics card, a white or gray line may appear on the screen when using the playback controls while viewing a DVD in Media Center.
To resolve this issue, try a different graphic mode, or press the Back button in Media Center, and press the OK button on the remote control.
___________________________________________________
In this document:
Video playback pauses briefly (stutters) and the sound is not synchronized
Step 2: Turning off or customizing the power management settings
My TV display is black and white
A white or gray line appears on the screen
This document applies to HP Media Center computers using Microsoft Windows XP Media Center Edition.
Use the solutions listed below to resolve poor picture quality problems on Media Center computers.
Before you begin, make sure that the problem is not with the DVD movie, video file, or TV signal itself. If possible, make sure the DVD disc and video file can be played on another system and there is no problem with the TV signal.
Video playback pauses briefly (stutters) and the sound is not synchronized
Most playback problems can be resolved by updating the video and sound driver and freeing up the system resources.
Step 1: Updating the video and sound drivers
Playback software driver:
Media Center and Windows Media Player - Get the latest updates for Media Center and Windows Media Player using Windows Update . Updates contain the latest fixes and feature enhancements.
InterVideo WinDVD - To download the latest versions of WinDVD included with the HP Media Center computer go to HP Software and Driver Download Web Page . To upgrade to a full version of WinDVD or for updates use InterVideo's Web Site (in English).
TV tuner card driver - Go to the HP Software and Driver Download Web Page , enter the model name of the HP Media Center computer and download the latest TV tuner driver.
Graphics card driver - Go to the HP Software and Driver Download Web Page , enter the model name of your HP Media Center computer and download the latest graphics card driver.
Sound card driver - Go to HP Software and Driver Download Web Page , enter the model name of the HP Media Center computer, and download the latest graphics card driver.
Step 2: Turning off or customizing the power management settings
For more information about setting power management options, go to Power Management Overview (Windows XP) . To turn off or customize your power managment options, follow the steps below:
Open the Control Panel. Click Start on the taskbar, and then click Control Panel.
Click Performance and Maintenance and then click Power Options to open the Power Options Properties window.
Click the drop-down arrows to select your power managment options.
Click Apply, and then click OK to save your settings.
Step 3: Freeing up system resources
The computer system has limited resources. Running other programs while playing movies will use up these resources and may affect the picture quality. Use the following HP support document for details on how to make the computer run quicker and more efficient: Increasing System Resources Without Adding Memory
My TV display is black and white
Reinstall the TV tuner driver.
Restart the computer. Do not open any software programs, especially the Media Center software program. If you have any programs that start up automatically make sure you close them.
Click Start, All Programs, PC Help and Tools (or hewlett-packard, hp pavilion PC Tools, and then HP Application Recovery.
Select Driver Installation, and click Next.
Select the name of the TV tuner used on the computer (eMuzed or Hauppauge or Conexant).
Click Install, and then click OK after the driver has finished installing.
Click Quit to close the HP Application Recovery program and restart the computer.
Connect to the Internet and click Start, All Programs, and then Windows Update.
Install a new tuner driver from the list of driver updates. Select the name of the TV tuner that came with your computer and install the new driver.
Restart the computer.
A white or gray line appears on the screen
If your PC model includes a GeForce 6600 graphics card, a white or gray line may appear on the screen when using the playback controls while viewing a DVD in Media Center.
To resolve this issue, try a different graphic mode, or press the Back button in Media Center, and press the OK button on the remote control.
Reducing Heat Inside the PC
Reducing Heat Inside the PC
___________________________________________________
Heat buildup can cause problems for any computer. This document can help prevent heat related problems from occurring.
Some problems heat can cause include:
Games stop responding while being played.
Windows stops responding while being used.
When starting the computer, it sometimes stops at a black screen and does not open into Windows (Windows will usually stop responding when it does open).
Mouse and keyboard stop responding.
Computer unexpectedly restarts or provides a blue fault message (Windows Vista, XP).
or
Frequent Fatal Exception, Illegal Operation, or General Protection Fault error messages occur in several different software programs (Windows 95, 98, and Me).
These errors will not be predictable. If these errors occur only in one software program, the problem is probably related to that software program and is not heat related.
Causes of excessive heat:
Dust inside the computer. Dust problems are made worse if the computer is on a carpeted floor.
A new component, like a hard drive, has been added. The extra component causes the power supply to work harder and generate more heat. Extra heat also radiates off the new component and adds to the temperature inside the case.
Some cooling fans may slow down and wear over time, depending on the usage of the computer.
High ambient room temperature.
Before you begin
WARNING: Children and pets should not be in the area due to the hazard of electrical shock.
WARNING: The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
CAUTION: This product contains components that are easily damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Make sure you have the following items:
Philips or slotted screwdrivers
Canned air (available from most computer repair and electronics stores)
Small flashlight
Safety goggles
Dust mask
Step 1: Testing the PC with the cover removed
Remove the side panel from the computer to see if the heat related problems go away. Doing so also prepares the computer for other procedures used in this article.
Turn off the computer and unplug the power cable.
Remove the side panel screws
Figure 1: Examples of panel screws
Remove the case panels or cover to expose the inside of the PC by sliding it off.
Plug in the power cable and turn on the computer.
CAUTION: Keep any items away from the internal area of the computer to avoid damaging the PC.
With the case cover removed, open a software program that is known to stop responding frequently to see if any problems still occur.
If the problems go away, excessive heat is probably building up inside the computer case. Use the steps in the rest of this document to help reduce the temperature inside the case.
If the problems do not go away, they are probably not being caused by heat. Refer to the Related Support section for further assistance.
Step 2: Verifying fans are operational
With the power on, look inside the computer and find the cooling fans. Look for the fans near vents, around the processor, and around the video card. You can use a flashlight to help find the fans but do not put anything inside the computer.
Figure 2: Fan locations
If a fan is not moving or is making a loud growling noise, turn off the computer and replace the fan. Do not use the computer when a fan is not working properly because the high heat can damage other important components.
Go to the next step after all fans are found to be working properly.
Step 3: Cleaning the computer
Dust may have built up around some of the internal components. Dust clogs the small air passages between metal surfaces, acting as a blanket to keep in heat. Use the steps below to remove dust:
WARNING: Wear safety goggles and a dust mask when using canned air to remove dust to protect eyes and nasal passages from dust.
Turn off the computer and disconnect the power cord.
Clean any exterior vents, especially around the power supply.
Figure 3: Power supply vent
Use canned air to blow the dust off the internal parts of the power supply.
If a small vacuum cleaner is available, use the suction end to remove dust from vent holes.
CAUTION: Do not use a vacuum cleaner to clean inside the PC. Doing so may damage the PC.
Remove dust from inside the computer. Use the canned air to clean off any dusty parts inside the computer.
After the computer has been cleaned, replace the case cover.
Plug in the power cord and turn on the computer. Use the computer as normal to see if any heat related problems still exist. If any problems continue, go to the next step.
Step 4: Placing the computer in a cooler room
A small difference in temperature may be all that is needed to prevent a component from failing. Move the computer to a cooler room in the house or office. If this is not an option, continue with the next step.
Step 5: Installing an extra fan
Case fans are available for purchase from most local computer supply stores. One type of fan that works well in home computers is a slot fan. These fans can be installed into a slot next to the video card. The hot air that surrounds the video card is drawn out through the slot fan lowering the air temperature inside the case.
Installation of the fan depends on the type of fan that is purchsed. After installing the fan according to its instructions, replace the case cover, plug in the power cord, and turn on the computer. Use the computer normally to see if the heat related problems go away.
Figure 4: Heat removed through a slot fan
1 - Video card
2 - Slot fan
___________________________________________________
Heat buildup can cause problems for any computer. This document can help prevent heat related problems from occurring.
Some problems heat can cause include:
Games stop responding while being played.
Windows stops responding while being used.
When starting the computer, it sometimes stops at a black screen and does not open into Windows (Windows will usually stop responding when it does open).
Mouse and keyboard stop responding.
Computer unexpectedly restarts or provides a blue fault message (Windows Vista, XP).
or
Frequent Fatal Exception, Illegal Operation, or General Protection Fault error messages occur in several different software programs (Windows 95, 98, and Me).
These errors will not be predictable. If these errors occur only in one software program, the problem is probably related to that software program and is not heat related.
Causes of excessive heat:
Dust inside the computer. Dust problems are made worse if the computer is on a carpeted floor.
A new component, like a hard drive, has been added. The extra component causes the power supply to work harder and generate more heat. Extra heat also radiates off the new component and adds to the temperature inside the case.
Some cooling fans may slow down and wear over time, depending on the usage of the computer.
High ambient room temperature.
Before you begin
WARNING: Children and pets should not be in the area due to the hazard of electrical shock.
WARNING: The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
CAUTION: This product contains components that are easily damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Make sure you have the following items:
Philips or slotted screwdrivers
Canned air (available from most computer repair and electronics stores)
Small flashlight
Safety goggles
Dust mask
Step 1: Testing the PC with the cover removed
Remove the side panel from the computer to see if the heat related problems go away. Doing so also prepares the computer for other procedures used in this article.
Turn off the computer and unplug the power cable.
Remove the side panel screws
Figure 1: Examples of panel screws
Remove the case panels or cover to expose the inside of the PC by sliding it off.
Plug in the power cable and turn on the computer.
CAUTION: Keep any items away from the internal area of the computer to avoid damaging the PC.
With the case cover removed, open a software program that is known to stop responding frequently to see if any problems still occur.
If the problems go away, excessive heat is probably building up inside the computer case. Use the steps in the rest of this document to help reduce the temperature inside the case.
If the problems do not go away, they are probably not being caused by heat. Refer to the Related Support section for further assistance.
Step 2: Verifying fans are operational
With the power on, look inside the computer and find the cooling fans. Look for the fans near vents, around the processor, and around the video card. You can use a flashlight to help find the fans but do not put anything inside the computer.
Figure 2: Fan locations
If a fan is not moving or is making a loud growling noise, turn off the computer and replace the fan. Do not use the computer when a fan is not working properly because the high heat can damage other important components.
Go to the next step after all fans are found to be working properly.
Step 3: Cleaning the computer
Dust may have built up around some of the internal components. Dust clogs the small air passages between metal surfaces, acting as a blanket to keep in heat. Use the steps below to remove dust:
WARNING: Wear safety goggles and a dust mask when using canned air to remove dust to protect eyes and nasal passages from dust.
Turn off the computer and disconnect the power cord.
Clean any exterior vents, especially around the power supply.
Figure 3: Power supply vent
Use canned air to blow the dust off the internal parts of the power supply.
If a small vacuum cleaner is available, use the suction end to remove dust from vent holes.
CAUTION: Do not use a vacuum cleaner to clean inside the PC. Doing so may damage the PC.
Remove dust from inside the computer. Use the canned air to clean off any dusty parts inside the computer.
After the computer has been cleaned, replace the case cover.
Plug in the power cord and turn on the computer. Use the computer as normal to see if any heat related problems still exist. If any problems continue, go to the next step.
Step 4: Placing the computer in a cooler room
A small difference in temperature may be all that is needed to prevent a component from failing. Move the computer to a cooler room in the house or office. If this is not an option, continue with the next step.
Step 5: Installing an extra fan
Case fans are available for purchase from most local computer supply stores. One type of fan that works well in home computers is a slot fan. These fans can be installed into a slot next to the video card. The hot air that surrounds the video card is drawn out through the slot fan lowering the air temperature inside the case.
Installation of the fan depends on the type of fan that is purchsed. After installing the fan according to its instructions, replace the case cover, plug in the power cord, and turn on the computer. Use the computer normally to see if the heat related problems go away.
Figure 4: Heat removed through a slot fan
1 - Video card
2 - Slot fan
Error in Windows 95, 98 or Me: Error loading GDI.exe
Error in Windows 95, 98 or Me: Error loading GDI.exe
___________________________________________________
In this document:
Resolving the error
Resolving the error using a recovery disc (Pavilion PCs)
Related support
The document pertains to PCs with Windows 95, 98, or Me.
When starting Windows, the following error message may appear after the Windows screen:
Error loading GDI.exe. System will power off and will not start Windows.
This error may occur if the fonts folder is deleted or damaged, or if you are using a VGA video adapter driver and one or more of the following files are missing or damaged:
Vgasys.fon
Vgaoem.fon
Vga850.fon
Use the information provided in this document to resolve this error or similar errors.
To resolve this error replace the missing font files using the recovery disc. If you do not have a recovery disc use the steps in the Replace the missing files without a recovery disc section to resolve the error.
Resolving the error
Use the following steps to replace the missing files:
Restart the PC and press F8 repeatedly when the PC is first turned on.
At the startup screen select Command Prompt Only.
At the command prompt type:
cd:\ Windows
Determine if a fonts directory is present by typing:
DIR FONTS
If File not found appears, the fonts folder must be created. To create the fonts folder proceed to step 4b. If the folder is present no message will appear and you can proceed to step 5.
At the C:\WINDOWS prompt type:
MD FONTS
Check to ensure the fonts folder was created by typing:
DIR FONTS
The file has been created properly if c:\windows\fonts appears (the file will be empty).
At the C:\WINDOWS prompt, type:
CD OPTIONS/CABS
Type:
EXTRACT /A BASE4.CAB *.TTF *.FON /L C:\WINDOWS\FONTS
Press Enter.
The font files will be extracted from the appropriate cab files and placed in the fonts folder (this can take a few minutes).
At the DOS prompt, type:
exit
If prompted to confirm a system return to Windows select Y for yes.
If these steps do not resolve the error, see Related Support for links to additional resources.
Resolving the error using a recovery disc (Pavilion PCs)
Use the following steps to replace the missing files and resolve the error using the recovery disc:
Put recovery disc one in the CD drive and restart the PC.
Click OK and select Advanced.
Choose Selective recovery and press Enter.
In the box type:
c:\windows\fonts\*.*.
Press OK to begin the selective recovery.
Remove the CD after the recovery is finished and click OK to restart the PC.
___________________________________________________
In this document:
Resolving the error
Resolving the error using a recovery disc (Pavilion PCs)
Related support
The document pertains to PCs with Windows 95, 98, or Me.
When starting Windows, the following error message may appear after the Windows screen:
Error loading GDI.exe. System will power off and will not start Windows.
This error may occur if the fonts folder is deleted or damaged, or if you are using a VGA video adapter driver and one or more of the following files are missing or damaged:
Vgasys.fon
Vgaoem.fon
Vga850.fon
Use the information provided in this document to resolve this error or similar errors.
To resolve this error replace the missing font files using the recovery disc. If you do not have a recovery disc use the steps in the Replace the missing files without a recovery disc section to resolve the error.
Resolving the error
Use the following steps to replace the missing files:
Restart the PC and press F8 repeatedly when the PC is first turned on.
At the startup screen select Command Prompt Only.
At the command prompt type:
cd:\ Windows
Determine if a fonts directory is present by typing:
DIR FONTS
If File not found appears, the fonts folder must be created. To create the fonts folder proceed to step 4b. If the folder is present no message will appear and you can proceed to step 5.
At the C:\WINDOWS prompt type:
MD FONTS
Check to ensure the fonts folder was created by typing:
DIR FONTS
The file has been created properly if c:\windows\fonts appears (the file will be empty).
At the C:\WINDOWS prompt, type:
CD OPTIONS/CABS
Type:
EXTRACT /A BASE4.CAB *.TTF *.FON /L C:\WINDOWS\FONTS
Press Enter.
The font files will be extracted from the appropriate cab files and placed in the fonts folder (this can take a few minutes).
At the DOS prompt, type:
exit
If prompted to confirm a system return to Windows select Y for yes.
If these steps do not resolve the error, see Related Support for links to additional resources.
Resolving the error using a recovery disc (Pavilion PCs)
Use the following steps to replace the missing files and resolve the error using the recovery disc:
Put recovery disc one in the CD drive and restart the PC.
Click OK and select Advanced.
Choose Selective recovery and press Enter.
In the box type:
c:\windows\fonts\*.*.
Press OK to begin the selective recovery.
Remove the CD after the recovery is finished and click OK to restart the PC.
Upgrading and Servicing Your PC (1999 - 2000)
Upgrading and Servicing Your PC (1999 - 2000)
___________________________________________________
In this document:
Introduction
Before you begin
Shutting down Windows
Removing the system cover
Removing the motherboard access panel
Replacing the motherboard access panel
Removing the front panel
Replacing the front panel
This document pertains to HP 65xx and 66xx Desktop PCs that came with the following case:
Introduction
The following steps and illustrations provide you with a basic overview of what you need to do to take apart and reassemble your computer.
Before you begin
WARNING: To avoid damage to the system board or power supply, do not exceed a total of 120 watts power draw.
CAUTION: Do not overload the power supply by installing add-in boards that draw excessive current.
CAUTION: This product contains components that are easily damaged by Electrostatic Discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Shutting down Windows
Before working on the system, you must properly turn off Windows and turn off the power to the computer, monitor, and any other peripherals. Follow the procedure below to shut down Windows:
On the bottom left corner of the Windows main screen is the Start button. Click Start once.
Click Shut Down. The Shut Down Windows dialog box appears.
Select Shut Down and click OK.
Wait a few seconds until the "It’s now safe to turn off your computer" message appears. You can turn off the power to the computer by pressing and holding the power button on the front of the PC.
Removing the system cover
Observe all Safety and ESD precautions stated in the Warnings and Cautions as noted above.
Turn off all devices that are connected to the PC.
Turn off the power to the PC.
Identify and tag all cables. Disconnect the cables from the system. Be sure to disconnect the modem cable BEFORE disconnecting the power cord.
Remove the 3 screws from the back of the case (1 on each side near the bottom and at the center of the top) on the back of the unit.
Figure 1: Cover and screws
From the rear of the system, pull back firmly on the cover to release it from the tabs on the frame, then lift the cover straight up and off the unit.
Removing the motherboard access panel
To open the panel without removing it
The right side of the computer, while facing the front of the system, is the Motherboard Access Panel. The motherboard is mounted to this panel and the panel must be opened slightly or removed to gain access to the right side of the inside case. To open the panel without removing it, follow the procedure below:
Remove the 4 screws that secure the Motherboard Access Panel to the case. Two are on the right side, and two are on the back panel.
Figure 2: Access panel screws
Grasp the opening near the front edge of the panel and open it away from the case.
Figure 3: Access panel
Pull panel out about 3 to 4 inches (7.62 to 10.16 centimeters) from the front edge of the case. You will now have access inside the case to remove drive bay screws on devices and the tabs for removing the drive bay filler bezel and the Front Panel locking tabs.
To completely remove the panel
To completely remove the Motherboard Access Panel, follow the procedure below:
Remove the 4 screws that secure the Motherboard Access Panel to the case. Two are on the right side, and two are on the back panel.
Grasp the opening near the front edge of the panel and pull it slightly away from the case. The panel will pivot around an interlocking hinge point on the back panel. Pull the panel out about 3 to 4 inches (7.62 to 10.16 centimeters) from the front edge of the case.
Figure 4: Access panel
Reach inside the case, and unplug all cables from the motherboard. Carefully label each cable and note its location on the motherboard.
Continue to open the access panel until the panel hinge can be removed from the slot on the rear case.
Figure 5: Slot for access panel
Pull the panel with the motherboard away from the case (see figure 6).
Figure 6: Access panel removed
Replacing the motherboard access panel
To replace the motherboard access panel, follow the procedure below:
Holding the access panel at an angle to the case, slide the hinge (on the back side, near the expansion board slots) into the slot on the back of the case.
Figure 7: Slot for access panel
Close the access panel, making sure the 2 parts of the hinge remain interlocked. Stop when the panel is at about a 45-degree angle from the side of the chassis.
Reconnect all cables to the motherboard.
fully close the acecess panel.
Secure the access panel using 4 screws.
Removing the front panel
To remove the power switch and front panel LEDs, you will first need to remove the front panel. Before removing the front panel, you will need to remove the device bay cover and the filler panel, which is below the CD-ROM drive.
Remove the 4 screws that secure the Motherboard Access Panel to the chassis and pivot the panel out to a 45-degree angle.
Remove the device bay cover by pressing down gently on the depression at the very top center of the cover, just below the CD-ROM drive. This will cause the cover to pop off.
With the device bay cover removed, you will have access to the filler panel. Remove the filler panel by releasing its 2 plastic tabs, one on each side of the chassis.
The front panel can now be removed. The front panel is held in place by 6 tabs, 3 on each side on the inside of the chassis.
Depress the bottom tab on both sides at the same time and pull the panel away from the chassis slightly, preventing the tabs from snapping back in place.
Depress the middle tab on both sides at the same time and pull the panel away from the chassis slightly, preventing the tabs from snapping back in place.
Depress the top tab on both sides and pull the panel away from the chassis.
Replacing the front panel
To replace the front panel, reverse the procedure for removing the panel.
Position the 6 tabs on the front panel with the chassis slots and press the panel forward making sure all 6 tabs snap into position.
Replace the top and bottom filler panel as appropriate making sure the 4 tabs, 2 on each side, snap into place in the device cage.
Replace the device bay cover, if appropriate.
___________________________________________________
In this document:
Introduction
Before you begin
Shutting down Windows
Removing the system cover
Removing the motherboard access panel
Replacing the motherboard access panel
Removing the front panel
Replacing the front panel
This document pertains to HP 65xx and 66xx Desktop PCs that came with the following case:
Introduction
The following steps and illustrations provide you with a basic overview of what you need to do to take apart and reassemble your computer.
Before you begin
WARNING: To avoid damage to the system board or power supply, do not exceed a total of 120 watts power draw.
CAUTION: Do not overload the power supply by installing add-in boards that draw excessive current.
CAUTION: This product contains components that are easily damaged by Electrostatic Discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Shutting down Windows
Before working on the system, you must properly turn off Windows and turn off the power to the computer, monitor, and any other peripherals. Follow the procedure below to shut down Windows:
On the bottom left corner of the Windows main screen is the Start button. Click Start once.
Click Shut Down. The Shut Down Windows dialog box appears.
Select Shut Down and click OK.
Wait a few seconds until the "It’s now safe to turn off your computer" message appears. You can turn off the power to the computer by pressing and holding the power button on the front of the PC.
Removing the system cover
Observe all Safety and ESD precautions stated in the Warnings and Cautions as noted above.
Turn off all devices that are connected to the PC.
Turn off the power to the PC.
Identify and tag all cables. Disconnect the cables from the system. Be sure to disconnect the modem cable BEFORE disconnecting the power cord.
Remove the 3 screws from the back of the case (1 on each side near the bottom and at the center of the top) on the back of the unit.
Figure 1: Cover and screws
From the rear of the system, pull back firmly on the cover to release it from the tabs on the frame, then lift the cover straight up and off the unit.
Removing the motherboard access panel
To open the panel without removing it
The right side of the computer, while facing the front of the system, is the Motherboard Access Panel. The motherboard is mounted to this panel and the panel must be opened slightly or removed to gain access to the right side of the inside case. To open the panel without removing it, follow the procedure below:
Remove the 4 screws that secure the Motherboard Access Panel to the case. Two are on the right side, and two are on the back panel.
Figure 2: Access panel screws
Grasp the opening near the front edge of the panel and open it away from the case.
Figure 3: Access panel
Pull panel out about 3 to 4 inches (7.62 to 10.16 centimeters) from the front edge of the case. You will now have access inside the case to remove drive bay screws on devices and the tabs for removing the drive bay filler bezel and the Front Panel locking tabs.
To completely remove the panel
To completely remove the Motherboard Access Panel, follow the procedure below:
Remove the 4 screws that secure the Motherboard Access Panel to the case. Two are on the right side, and two are on the back panel.
Grasp the opening near the front edge of the panel and pull it slightly away from the case. The panel will pivot around an interlocking hinge point on the back panel. Pull the panel out about 3 to 4 inches (7.62 to 10.16 centimeters) from the front edge of the case.
Figure 4: Access panel
Reach inside the case, and unplug all cables from the motherboard. Carefully label each cable and note its location on the motherboard.
Continue to open the access panel until the panel hinge can be removed from the slot on the rear case.
Figure 5: Slot for access panel
Pull the panel with the motherboard away from the case (see figure 6).
Figure 6: Access panel removed
Replacing the motherboard access panel
To replace the motherboard access panel, follow the procedure below:
Holding the access panel at an angle to the case, slide the hinge (on the back side, near the expansion board slots) into the slot on the back of the case.
Figure 7: Slot for access panel
Close the access panel, making sure the 2 parts of the hinge remain interlocked. Stop when the panel is at about a 45-degree angle from the side of the chassis.
Reconnect all cables to the motherboard.
fully close the acecess panel.
Secure the access panel using 4 screws.
Removing the front panel
To remove the power switch and front panel LEDs, you will first need to remove the front panel. Before removing the front panel, you will need to remove the device bay cover and the filler panel, which is below the CD-ROM drive.
Remove the 4 screws that secure the Motherboard Access Panel to the chassis and pivot the panel out to a 45-degree angle.
Remove the device bay cover by pressing down gently on the depression at the very top center of the cover, just below the CD-ROM drive. This will cause the cover to pop off.
With the device bay cover removed, you will have access to the filler panel. Remove the filler panel by releasing its 2 plastic tabs, one on each side of the chassis.
The front panel can now be removed. The front panel is held in place by 6 tabs, 3 on each side on the inside of the chassis.
Depress the bottom tab on both sides at the same time and pull the panel away from the chassis slightly, preventing the tabs from snapping back in place.
Depress the middle tab on both sides at the same time and pull the panel away from the chassis slightly, preventing the tabs from snapping back in place.
Depress the top tab on both sides and pull the panel away from the chassis.
Replacing the front panel
To replace the front panel, reverse the procedure for removing the panel.
Position the 6 tabs on the front panel with the chassis slots and press the panel forward making sure all 6 tabs snap into position.
Replace the top and bottom filler panel as appropriate making sure the 4 tabs, 2 on each side, snap into place in the device cage.
Replace the device bay cover, if appropriate.
Troubleshooting Power and Battery Problems
Troubleshooting Power and Battery Problems
___________________________________________________
In this document:
If the computer turns off immediately after it turns on
If the computer keeps beeping
If the battery doesn't charge
If a secondary battery doesn't charge
If the computer has a short operating time
If the Time Remaining for the battery is not correct
If the computer doesn't suspend to Standby mode as expected
If the computer doesn’t automatically hibernate as expected
If the computer turns off immediately after it turns on
Battery power is probably extremely low. Plug in the AC adapter or insert a charged battery.
If the computer keeps beeping
The computer beeps for 15 seconds when battery power is low. Save work, shut down Windows immediately, and insert a charged battery or plug in the AC adapter.
If the battery doesn't charge
Make sure the AC adapter is fully plugged into the power source and the computer, and that the light on the adapter is on.
If using a power strip, remove the AC adapter from the power strip and plug it directly into a wall outlet.
Make sure the battery is fully installed and locked in place.
Move the computer away from any nearby heat source. Unplug the AC adapter and allow the battery to cool down. If the battery gets too hot, it will not charge properly.
If available, try another battery and AC adapter.
If a secondary battery doesn't charge
The computer’s secondary battery won't charge until the main battery is fully charged.
Make sure the AC adapter is fully plugged into the power source and the computer, and that the light on the adapter is on.
Make sure the secondary battery is correctly installed and locked in place.
If the computer has a short operating time
Try conserving power using any of the suggestions listed below:
Plug in the AC adapter, especially while using a drive in the module bay or any external connections such as a PC Card or a modem.
Set the display brightness to the lowest comfortable level (Fn+F1).
Put the computer in Standby mode whenever it is not being used for a short while: press the blue sleep button for approximately one second or click Start, (Windows 95) or , Shut Down, (Windows 98 and 2000).
Put the computer in Hibernate mode whenever there is a need to save the current session but the computer will not be used for several hours. To do this press Fn+F12.
Set the automatic timeout settings to emphasize saving power. If the computer has a dual-speed processor, use the lower speed on battery power (the default settings conserve battery power).
If using an I/O PC Card, a PC Card having an external connection such as a network card, remove it when it is not being used. Some I/O cards use significant power even while they're inactive.
If working with an application that uses the serial port or an I/O PC Card, exit the application when finished using it.
Install a secondary battery.
If the main battery is rated at 11.1 volts (check its label), purchase a replacement main battery, which is rated at 14.8 volts.
If running an application that has an automatic save feature (such as MS Word), disable this feature or increase the specified save time to reduce hard disk access.
If the operating time has gradually become shorter and the battery is more than a year or two old, the battery may need replacing.
Heavy modem use can affect battery operating time.
If the Time Remaining for the battery is not correct
The Time Remaining is an estimate, not a precise value, and is based on the rate at which the computer is using power at the moment. This value therefore depends on the current task, and assumes that the power will continue to be used at the same rate until the battery runs out. So, check the Time Remaining while the computer is performing a task requiring a good deal of power (such as reading from a CD or DVD), the value will probably show less time remaining than it really has, since you will probably later switch to tasks that require less power.
If the computer doesn't suspend to Standby mode as expected
If using a connection to another computer, the computer won’t suspend if the connection is active.
If the computer is performing an operation, it normally waits for the operation to finish before suspending.
For Windows 95, if a CD-ROM drive is present, make sure auto insert notification is disabled (the default factory setting). This is not required for Windows 98 or 2000.
In Windows 95 or 98, view the CD-ROM drive properties in Device Manager.
If the computer doesn’t automatically hibernate as expected
For Windows 2000, make sure hibernate support is enabled. From Control Panel, open Power, then click the Hibernate tab.
Also, check the Power Schemes tab. Make sure the Hibernate timeouts for both AC power and battery power are not set to Never.
For Windows 95 or 98, check the Hibernate timeout in BIOS Setup.
___________________________________________________
In this document:
If the computer turns off immediately after it turns on
If the computer keeps beeping
If the battery doesn't charge
If a secondary battery doesn't charge
If the computer has a short operating time
If the Time Remaining for the battery is not correct
If the computer doesn't suspend to Standby mode as expected
If the computer doesn’t automatically hibernate as expected
If the computer turns off immediately after it turns on
Battery power is probably extremely low. Plug in the AC adapter or insert a charged battery.
If the computer keeps beeping
The computer beeps for 15 seconds when battery power is low. Save work, shut down Windows immediately, and insert a charged battery or plug in the AC adapter.
If the battery doesn't charge
Make sure the AC adapter is fully plugged into the power source and the computer, and that the light on the adapter is on.
If using a power strip, remove the AC adapter from the power strip and plug it directly into a wall outlet.
Make sure the battery is fully installed and locked in place.
Move the computer away from any nearby heat source. Unplug the AC adapter and allow the battery to cool down. If the battery gets too hot, it will not charge properly.
If available, try another battery and AC adapter.
If a secondary battery doesn't charge
The computer’s secondary battery won't charge until the main battery is fully charged.
Make sure the AC adapter is fully plugged into the power source and the computer, and that the light on the adapter is on.
Make sure the secondary battery is correctly installed and locked in place.
If the computer has a short operating time
Try conserving power using any of the suggestions listed below:
Plug in the AC adapter, especially while using a drive in the module bay or any external connections such as a PC Card or a modem.
Set the display brightness to the lowest comfortable level (Fn+F1).
Put the computer in Standby mode whenever it is not being used for a short while: press the blue sleep button for approximately one second or click Start, (Windows 95) or , Shut Down, (Windows 98 and 2000).
Put the computer in Hibernate mode whenever there is a need to save the current session but the computer will not be used for several hours. To do this press Fn+F12.
Set the automatic timeout settings to emphasize saving power. If the computer has a dual-speed processor, use the lower speed on battery power (the default settings conserve battery power).
If using an I/O PC Card, a PC Card having an external connection such as a network card, remove it when it is not being used. Some I/O cards use significant power even while they're inactive.
If working with an application that uses the serial port or an I/O PC Card, exit the application when finished using it.
Install a secondary battery.
If the main battery is rated at 11.1 volts (check its label), purchase a replacement main battery, which is rated at 14.8 volts.
If running an application that has an automatic save feature (such as MS Word), disable this feature or increase the specified save time to reduce hard disk access.
If the operating time has gradually become shorter and the battery is more than a year or two old, the battery may need replacing.
Heavy modem use can affect battery operating time.
If the Time Remaining for the battery is not correct
The Time Remaining is an estimate, not a precise value, and is based on the rate at which the computer is using power at the moment. This value therefore depends on the current task, and assumes that the power will continue to be used at the same rate until the battery runs out. So, check the Time Remaining while the computer is performing a task requiring a good deal of power (such as reading from a CD or DVD), the value will probably show less time remaining than it really has, since you will probably later switch to tasks that require less power.
If the computer doesn't suspend to Standby mode as expected
If using a connection to another computer, the computer won’t suspend if the connection is active.
If the computer is performing an operation, it normally waits for the operation to finish before suspending.
For Windows 95, if a CD-ROM drive is present, make sure auto insert notification is disabled (the default factory setting). This is not required for Windows 98 or 2000.
In Windows 95 or 98, view the CD-ROM drive properties in Device Manager.
If the computer doesn’t automatically hibernate as expected
For Windows 2000, make sure hibernate support is enabled. From Control Panel, open Power, then click the Hibernate tab.
Also, check the Power Schemes tab. Make sure the Hibernate timeouts for both AC power and battery power are not set to Never.
For Windows 95 or 98, check the Hibernate timeout in BIOS Setup.
Upgrading and Servicing Your PC (2001 - 2002)
Upgrading and Servicing Your PC (2001 - 2002)
___________________________________________________
In this document:
Introduction
Before beginning
Removing the right side panel
Moving the drive cage
Rreplacing the hard drive
Assembling the computer
This document pertains to 63xx and 64xx HP Desktop PCs.
Introduction
This document contains information about taking apart the PC for servicing or upgrading.
Before beginning
Be sure to read the items below before attempting to upgrade or service the computer:
You will need a Phillips screwdriver and a medium flat-blade screwdriver.
HP recommends using an antistatic wrist strap and a conductive foam pad when working on the system.
before beginning, disconnect all connected devices like printers and telephone cords.
WARNING: Do not operate the system with the cover removed. Always replace the cover before turning on the system.
CAUTION: Electrostatic discharge (ESD) can damage disk drives, add-in cards, and other components. If an ESD station is not available, wear a wrist strap attached to a metal part of the computer. Place cards on a conductive foam pad or inside the conductive wrapper they came in; do not place the cards on top of the wrapper.
Removing the right side panel
To remove the right side panel, follow the instructions below:
Turn off the PC and all connected devices.
Disconnect all cables including the power cable.
Move the PC to a stable, static safe surface.
Loosen the two screws on the right side of the back panel.
Pull backward on the right panel and rotate the front end of it to the right. It will disengage.
Moving the drive cage
The drive cage must be moved out to allow access to some components on the motherboard, or to acess the tabs that release the front bezel. You may need to slide the drive cage out in order to add memory, insert add-in cards, or change the battery.
To slide the drive cage out, follow the instructions below:
Remove the right side panel, as shown in the procedures above.
Using a Phillips screwdriver, remove the two screws.
With your right hand, reach under the top edge of the chassis and pull the latch located under screw 1 toward you. Continue to hold the latch in this position while you complete the next step.
1 - Top drive cage retaining screw
2 - Lower retaining screw
While gripping the top of the drive cage, slide the cage about halfway out.
Release the latch.
It may be necessary to disconnect some cables that can block access.
Rreplacing the hard drive
Note the position of the hard drive in the drive cage so you can install the new hard drive properly.
Remove the screws that hold the hard drive in place. There are two on one side and may be one or two screws on the other. See Figure 3.
Figure 1: Removing the screws that hold the hard drive in place
Slide the hard drive out through the rear of the drive cage.
Unpack the replacement hard drive from the antistatic bag and slide it into the drive cage from the rear.
Replace the screws you removed in Step 3.
Reconnect the IDE cable and the power cable to the new hard disk drive.
Assembling the computer
Reconnect any internal cables.
Slide the drive cage back into the computer until you hear a click.
Replace the screws above the latch.
Replace the left and right side panels by aligning the top slots of the panel and sliding them back into place.
Replace side panel screw.
Plug in the video, keyboard, and mouse cables.
Plug in the power cable and turn the PC on.
Once the PC is on and the upgraded devices are working properly, turn off the PC and reconnect all the other devices that were originaly connected to the PC (printers, scanners, and others).
___________________________________________________
In this document:
Introduction
Before beginning
Removing the right side panel
Moving the drive cage
Rreplacing the hard drive
Assembling the computer
This document pertains to 63xx and 64xx HP Desktop PCs.
Introduction
This document contains information about taking apart the PC for servicing or upgrading.
Before beginning
Be sure to read the items below before attempting to upgrade or service the computer:
You will need a Phillips screwdriver and a medium flat-blade screwdriver.
HP recommends using an antistatic wrist strap and a conductive foam pad when working on the system.
before beginning, disconnect all connected devices like printers and telephone cords.
WARNING: Do not operate the system with the cover removed. Always replace the cover before turning on the system.
CAUTION: Electrostatic discharge (ESD) can damage disk drives, add-in cards, and other components. If an ESD station is not available, wear a wrist strap attached to a metal part of the computer. Place cards on a conductive foam pad or inside the conductive wrapper they came in; do not place the cards on top of the wrapper.
Removing the right side panel
To remove the right side panel, follow the instructions below:
Turn off the PC and all connected devices.
Disconnect all cables including the power cable.
Move the PC to a stable, static safe surface.
Loosen the two screws on the right side of the back panel.
Pull backward on the right panel and rotate the front end of it to the right. It will disengage.
Moving the drive cage
The drive cage must be moved out to allow access to some components on the motherboard, or to acess the tabs that release the front bezel. You may need to slide the drive cage out in order to add memory, insert add-in cards, or change the battery.
To slide the drive cage out, follow the instructions below:
Remove the right side panel, as shown in the procedures above.
Using a Phillips screwdriver, remove the two screws.
With your right hand, reach under the top edge of the chassis and pull the latch located under screw 1 toward you. Continue to hold the latch in this position while you complete the next step.
1 - Top drive cage retaining screw
2 - Lower retaining screw
While gripping the top of the drive cage, slide the cage about halfway out.
Release the latch.
It may be necessary to disconnect some cables that can block access.
Rreplacing the hard drive
Note the position of the hard drive in the drive cage so you can install the new hard drive properly.
Remove the screws that hold the hard drive in place. There are two on one side and may be one or two screws on the other. See Figure 3.
Figure 1: Removing the screws that hold the hard drive in place
Slide the hard drive out through the rear of the drive cage.
Unpack the replacement hard drive from the antistatic bag and slide it into the drive cage from the rear.
Replace the screws you removed in Step 3.
Reconnect the IDE cable and the power cable to the new hard disk drive.
Assembling the computer
Reconnect any internal cables.
Slide the drive cage back into the computer until you hear a click.
Replace the screws above the latch.
Replace the left and right side panels by aligning the top slots of the panel and sliding them back into place.
Replace side panel screw.
Plug in the video, keyboard, and mouse cables.
Plug in the power cable and turn the PC on.
Once the PC is on and the upgraded devices are working properly, turn off the PC and reconnect all the other devices that were originaly connected to the PC (printers, scanners, and others).
Jumper Settings for the Installation of IDE Hard Disks and CD, CDRW, and DVD Drives
Jumper Settings for the Installation of IDE Hard Disks and CD, CDRW, and DVD Drives
___________________________________________________
The following information helps set the required Cable Selection settings on a hard drive or optical drive.
NOTE: This document contains a procedure that is highly technical. The person performing the procedure should have extensive computer experience working with both hardware and software.
WARNING: The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
CAUTION: This product contains components that are easily damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Location of the jumper, IDE connectors, and ribbon cables
The jumpers for the hard disk(s) and CD/DVD drives are located on the back of the drive. The jumper is a small rectangular plastic piece that slides over 2 pins. Refer to the manufacturer documentation that comes with the drive for the specific jumper settings to set the drive to Master, Slave, or Cable Select.
NOTE:
If Cable Select (CS) is used on the first device, then the 2nd device on the same cable must also use CS.
If Master (MA) is selected on the first device, then the second device on the same cable must be set to Slave (SL).
NOTE: When using one Western Digital hard drive on one cable, it may need to be set to "Single". See hard drive documentation for details.
The primary and secondary IDE controller connectors are both on the motherboard. An IDE ribbon cable plugs into one of these connectors. Each of these connectors are labeled on the motherboard.
Each drive uses a standard 40-pin IDE cable (Ultra-IDE or EIDE cables will have 80-wire cables with the same 40-pin connections), which looks like a flat, wide, flexible plastic strap or ribbon. The ribbon cable connects a hard drive or CD-ROM drive to the motherboard. It is possible to connect up to two devices on the same ribbon cable, as long as it has three connectors on it (one that plugs into the motherboard and two that plug into the back of the drives). Such cables can be purchased at retail stores that carry computer accessories.
Figure 1: Upper IDE cable connectors
1 - Slave connector (middle)
2 - Master connector (end)
If a cable needs to be purchased, buy a 40-pin IDE cable with the desired number of connectors. If you are connecting an Ultra-IDE capable HD to PC that is capable of Ulta-IDE, be sure to purchase an Ultra-IDE cable.
Settings for 1 Hard drive and 1 CD/DVD drive
Set the hard disk jumper as CS or Single. Connect the drive using the Master connector on the primary IDE cable.
Set the CD/DVD drive jumper as CS. Connect the drive using the Master connector on the secondary IDE cable.
Settings for 2 Hard drives and 1 CD/DVD drive
Set the first hard disk jumper as Master (alternatively, the Cable Select selection can be used but set the 2nd hard drive to Cable Select). Connect the drive using the Master connector on the primary IDE cable.
Set the second hard disk jumper to Slave (use the Cable Select selection if Cable Select was set on the 1st hard drive). Connect the drive using the Slave connector on the primary IDE cable.
Set the CD/DVD drive jumper as Cable Select. Connect the drive using the Master connector on the secondary IDE cable.
Settings for 1 Hard drive and 2 CD/DVD drives
Set the hard disk jumper as Cable Select or Single. Connect the drive using the Master connector on the primary IDE cable.
Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the 2nd CD/DVD drive selection to Cable Select). Connect the drive using the Master connector on the secondary IDE cable.
Set the second CD/DVD drive jumper to Slave (use Cable Select if Cable Select was used on the 1st CD/DVD drive). Connect the drive using the Slave connector on the secondary IDE cable.
Settings for 2 Hard drives and 2 CD/DVD drives
Set the first hard disk jumper to Master (Cable Select can be used if you set the 2nd hard drive selection to Cable Select). Connect the drive using the Master connector on the primary IDE cable.
Set the second hard disk jumper to Slave (Use Cable Select if Cable Select was used on the 1st HDD). Connect the drive using the Slave connector on the primary IDE cable.
Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the 2nd CD/DVD drive selection to Cable Select). Connect the drive using the Master connector on the secondary IDE cable.
Set the second CD/DVD drive jumper to Slave (use Cable Select if Cable Select was used on the 1st CD/DVD drive). Connect the drive using the Slave connector on the secondary IDE cable.
___________________________________________________
The following information helps set the required Cable Selection settings on a hard drive or optical drive.
NOTE: This document contains a procedure that is highly technical. The person performing the procedure should have extensive computer experience working with both hardware and software.
WARNING: The edges of metal panels can cut skin. Be careful not to slide skin along any interior metal edge of the computer.
CAUTION: This product contains components that are easily damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a non-carpeted floor, use a static dissipative work surface (like a conductive foam pad), and wear an ESD wrist strap that is connected to a grounded surface, like the metal frame of a computer.
Location of the jumper, IDE connectors, and ribbon cables
The jumpers for the hard disk(s) and CD/DVD drives are located on the back of the drive. The jumper is a small rectangular plastic piece that slides over 2 pins. Refer to the manufacturer documentation that comes with the drive for the specific jumper settings to set the drive to Master, Slave, or Cable Select.
NOTE:
If Cable Select (CS) is used on the first device, then the 2nd device on the same cable must also use CS.
If Master (MA) is selected on the first device, then the second device on the same cable must be set to Slave (SL).
NOTE: When using one Western Digital hard drive on one cable, it may need to be set to "Single". See hard drive documentation for details.
The primary and secondary IDE controller connectors are both on the motherboard. An IDE ribbon cable plugs into one of these connectors. Each of these connectors are labeled on the motherboard.
Each drive uses a standard 40-pin IDE cable (Ultra-IDE or EIDE cables will have 80-wire cables with the same 40-pin connections), which looks like a flat, wide, flexible plastic strap or ribbon. The ribbon cable connects a hard drive or CD-ROM drive to the motherboard. It is possible to connect up to two devices on the same ribbon cable, as long as it has three connectors on it (one that plugs into the motherboard and two that plug into the back of the drives). Such cables can be purchased at retail stores that carry computer accessories.
Figure 1: Upper IDE cable connectors
1 - Slave connector (middle)
2 - Master connector (end)
If a cable needs to be purchased, buy a 40-pin IDE cable with the desired number of connectors. If you are connecting an Ultra-IDE capable HD to PC that is capable of Ulta-IDE, be sure to purchase an Ultra-IDE cable.
Settings for 1 Hard drive and 1 CD/DVD drive
Set the hard disk jumper as CS or Single. Connect the drive using the Master connector on the primary IDE cable.
Set the CD/DVD drive jumper as CS. Connect the drive using the Master connector on the secondary IDE cable.
Settings for 2 Hard drives and 1 CD/DVD drive
Set the first hard disk jumper as Master (alternatively, the Cable Select selection can be used but set the 2nd hard drive to Cable Select). Connect the drive using the Master connector on the primary IDE cable.
Set the second hard disk jumper to Slave (use the Cable Select selection if Cable Select was set on the 1st hard drive). Connect the drive using the Slave connector on the primary IDE cable.
Set the CD/DVD drive jumper as Cable Select. Connect the drive using the Master connector on the secondary IDE cable.
Settings for 1 Hard drive and 2 CD/DVD drives
Set the hard disk jumper as Cable Select or Single. Connect the drive using the Master connector on the primary IDE cable.
Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the 2nd CD/DVD drive selection to Cable Select). Connect the drive using the Master connector on the secondary IDE cable.
Set the second CD/DVD drive jumper to Slave (use Cable Select if Cable Select was used on the 1st CD/DVD drive). Connect the drive using the Slave connector on the secondary IDE cable.
Settings for 2 Hard drives and 2 CD/DVD drives
Set the first hard disk jumper to Master (Cable Select can be used if you set the 2nd hard drive selection to Cable Select). Connect the drive using the Master connector on the primary IDE cable.
Set the second hard disk jumper to Slave (Use Cable Select if Cable Select was used on the 1st HDD). Connect the drive using the Slave connector on the primary IDE cable.
Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the 2nd CD/DVD drive selection to Cable Select). Connect the drive using the Master connector on the secondary IDE cable.
Set the second CD/DVD drive jumper to Slave (use Cable Select if Cable Select was used on the 1st CD/DVD drive). Connect the drive using the Slave connector on the secondary IDE cable.
Setting Input Voltage for Use in Another Country/Region
Setting Input Voltage for Use in Another Country/Region
___________________________________________________
This document applies to all HP and Compaq desktop PCs.
Using a computer in a country/region other than where it was originally purchased may require changing the input voltage selector switch. The voltage selector switch can be found on the back of the PC where the power cord connects to the PC.
Figure 1: Voltage selector switch example
NOTE: Some PCs come with power supplies that switch automatically and do not have a voltage selector switch.
There are two switch positions on the input voltage selector - a lower range (typically 100V-127V~7A - 115V) and an upper range (200V-240V~4A).
To switch the selection, unplug the power cord and use a small screwdriver to slide the switch to the opposite position.
The voltage level supplied by the power outlet needs to fall within the voltage range that is selected by the input voltage selector.
CAUTION: Changing the input voltage selector switch to the incorrect setting can damage the computer. Make sure that you know what voltage is being supplied by the power outlet before setting the voltage selector switch and before connecting the power cord.
For example, if a PC was purchased and used in the United States on 120 volt alternating current (VAC) and was then moved to another country that used 220 VAC, the voltage selector switch needs to to be switched from the lower range to the upper range (230V) before it can be powered on.
In addition, different countries/regions use different power outlets and plug ends. You may have to purchase and use a new power cord to match the outlet type. Adapters may also be available that can allow you to use your original cord with different outlet types, but using a correct cable type should be preferred over using an adapter.
NOTE: The following list is provided as an example of the differences between coutries/regions. Some countries/regions may use more than one type of voltage in different areas. Do not use the data in this list to determine the source voltage for your power outlet. If you are in doubt, refer to your electrical bill or support for your power services.
Countries/Regions
Voltage
Argentina
220 VAC
Australia
240 VAC
Canada
120 VAC
China
220 VAC
Cyprus
240 VAC
Denmark
220 VAC
Egypt
220 VAC
Europe, East and West
220 VAC
India
220 VAC
Japan
100 VAC
Libya
220 VAC
Mexico
120 VAC
New Zealand
240 VAC
Papua New Guinea
220 VAC
Philippines
120 VAC
Saudi Arabia
220 VAC
Singapore
240 VAC
South Africa
220 VAC
Spain
220 VAC
Sudan
240 VAC
Switzerland
220 VAC
Taiwan
120 VAC
United Kingdom
240 VAC
United States
120 VAC
Uruguay
220 VAC
___________________________________________________
This document applies to all HP and Compaq desktop PCs.
Using a computer in a country/region other than where it was originally purchased may require changing the input voltage selector switch. The voltage selector switch can be found on the back of the PC where the power cord connects to the PC.
Figure 1: Voltage selector switch example
NOTE: Some PCs come with power supplies that switch automatically and do not have a voltage selector switch.
There are two switch positions on the input voltage selector - a lower range (typically 100V-127V~7A - 115V) and an upper range (200V-240V~4A).
To switch the selection, unplug the power cord and use a small screwdriver to slide the switch to the opposite position.
The voltage level supplied by the power outlet needs to fall within the voltage range that is selected by the input voltage selector.
CAUTION: Changing the input voltage selector switch to the incorrect setting can damage the computer. Make sure that you know what voltage is being supplied by the power outlet before setting the voltage selector switch and before connecting the power cord.
For example, if a PC was purchased and used in the United States on 120 volt alternating current (VAC) and was then moved to another country that used 220 VAC, the voltage selector switch needs to to be switched from the lower range to the upper range (230V) before it can be powered on.
In addition, different countries/regions use different power outlets and plug ends. You may have to purchase and use a new power cord to match the outlet type. Adapters may also be available that can allow you to use your original cord with different outlet types, but using a correct cable type should be preferred over using an adapter.
NOTE: The following list is provided as an example of the differences between coutries/regions. Some countries/regions may use more than one type of voltage in different areas. Do not use the data in this list to determine the source voltage for your power outlet. If you are in doubt, refer to your electrical bill or support for your power services.
Countries/Regions
Voltage
Argentina
220 VAC
Australia
240 VAC
Canada
120 VAC
China
220 VAC
Cyprus
240 VAC
Denmark
220 VAC
Egypt
220 VAC
Europe, East and West
220 VAC
India
220 VAC
Japan
100 VAC
Libya
220 VAC
Mexico
120 VAC
New Zealand
240 VAC
Papua New Guinea
220 VAC
Philippines
120 VAC
Saudi Arabia
220 VAC
Singapore
240 VAC
South Africa
220 VAC
Spain
220 VAC
Sudan
240 VAC
Switzerland
220 VAC
Taiwan
120 VAC
United Kingdom
240 VAC
United States
120 VAC
Uruguay
220 VAC
Checking the Status of the Battery in Windows XP
Checking the Status of the Battery in Windows XP
___________________________________________________
Description
In 2005, HP added Smart Battery support to our notebook PCs. On an HP notebook PC, the status of the battery is accessible from a downloadable utility that HP provides. The utility provides a simple, but accurate test status of the battery status.
NOTE: As with all batteries, the maximum capacity of this battery will decrease with time or use. Loss of battery capacity will vary depending on the product configuration and usage, including but not limited to: product model, applications running, power management settings, and product features.The battery warranty does not cover natural deterioration of battery capacity. Your battery is only warranted from defects in materials or workmanship resulting in failure.To determine if your battery has had a warranted failure you may be required to run an HP diagnostic.
Solution
Select one of the methods below to check the status of an HP notebook PC battery to determine if needs to be replaced:
Method 1: Check the battery status using the HP Battery Check . (For HP notebook PCs manufactured in 2005 or later)
Method 2: Check the battery status manually (For HP notebook PCS not supported by the HP Battery Check or manufactured before 2005)
Also see Method 3: Reduce the operating temperature and increase the battery life for information the best conditions for charging your battery.
Method 1: Check the battery status using the HP Battery Check
Use the following steps to download, install and use the HP Battery Check on all notebooks manufactured after 2004.
For more information about using the HP Battery test, including a list of notebook PCs that are supported, see HP Notebook PCs - HP Battery Check Frequently Asked Questions .
Download and install the HP Battery Check
Download the HP Battery Check SoftPaq at the following location:
HP Battery Check (SP32299)
Click Run.
If a security warning displays, click Run.
Click Next.
Click next to the I accept the terms of the license agreement, then click Next.
Click Next again.
NOTE: If a This system is not supported by the HP Battery Check tool warning screen displays, the notebook model is not supported by the HP Battery Check and you should use Method 2: Check the battery status manually .
Test the battery using the HP Battery Check
Insert the AC power adapter into the notebook PC and plug directly into a wall outlet.
Click Start, All Programs, then click Hewlett-Packard, HP Battery Check.
The results of the Battery test will be presented immediately. Detailed instructions are provided with the results. One of the following results will appear in the Battery Health section:
Good - the battery is in working order.
Replace - one or more of the cells can no longer accept a charge or the storage capacity is "Low" and the battery should to be replaced. Instructions stating where to purchase a replacement battery or if the battery is covered by HP under warranty will display.
Invalid - either the AC adapter is not connected, more than one battery is installed or the battery is not installed correctly. Please follow the instructions in the Battery Check to correct the condition.
NOTE: If the Battery Check detects a failure, you will be prompted to contact HP support to discuss the warranty service options available to you. A WARRANTY ID and SAT ID is provided to you by the Battery Check. This information will assist the HP support representative with your replacement options.
Method 2: Check the battery status manually
Use the following steps to check the battery status on a notebook, manufactured in 2004 or earlier, while it is not in use.
To accurately measure the condition of the battery, the PC cannot be used during this test. This method will Test the battery by completely charging the battery then will determine how long it takes to discharge the battery. This test is done while the PC is operating in the Safe Mode and not being used for any other action.
This test will require 1-3 hours depending on condition of the notebook PC. The PC cannot be used while you perform the following steps. Completing all the following steps will also calibrate the battery so that the power meter reading are accurate.
Connect the AC adapter and allow the notebook to charge until the battery is charged to 99% - 100% of capacity.
To determine the percentage of battery power, with the notebook operating normally, right-click on the power icon in the system tray, and select Open power meter. The Power Status is displayed.
Shut down the notebook PC when the battery has charged to capacity.
With the notebook turned off, connect the notebook PC to the AC power adapter that is plugged into a working wall outlet.
Press and release the Power Button to start the computer.
Press the F8 key several times when the HP Logo displays.
When the Windows Advanced Startup Menu displays, select the Startup in Safe Mode option.
Notice and record the current time as the Test Start Time with a fully charged battery.
Remove the AC power adapter cable from the notebook PC.
Allow the battery to discharge completely until the notebook PC turns off.
Notice and record the Completely Discharged Time.
Subtract the Discharged Time from the Start Time to calculate the Elapsed time.
Record the time for future comparison or to provide to an HP support specialist if you suspect the battery is defective.
NOTE: As with all batteries, the maximum capacity of this battery will decrease with time or use. Loss of battery capacity will vary depending on the product configuration and usage, including but not limited to: product model, applications running, power management settings, and product features.The battery warranty does not cover natural deterioration of battery capacity. Your battery is only warranted from defects in materials or workmanship resulting in failure.To determine if your battery has had a warranted failure you may be required to run an HP diagnostic.
Method 3: Reduce the operating temperature and increase battery life
The battery in your notebook PC is designed to provide the necessary amount of energy for the processor while maintaining HP high safety standards. As a result, the battery may not charge or may stop providing power to the notebook when the battery temperature exceeds the specified, design safety level.
If the battery life appears shorter than normal, the battery stops charging before it is 99%-100% full and the battery appears warmer than usual, the battery has most likely reached its designed "no charge" safety state. The battery will no longer charge until the temperature condition is corrected.
Try one of the following methods to correct the battery temperature:
When charging the battery, do not use applications that require large amounts of system resources such as graphic or memory intensive applications, heavy and extended hard drive usage.
Turn off your notebook and remove the battery to allow it to return to a safe operating temperature.
Make sure the notebook PC is operating on a hard surface. Using the Notebook PC on a bed or sofa may block the vents causing the notebook PC to heat up and shut down.
By taking these steps, the battery will return to its normal operating temperature range and continue to charge and discharge as designed.
___________________________________________________
Description
In 2005, HP added Smart Battery support to our notebook PCs. On an HP notebook PC, the status of the battery is accessible from a downloadable utility that HP provides. The utility provides a simple, but accurate test status of the battery status.
NOTE: As with all batteries, the maximum capacity of this battery will decrease with time or use. Loss of battery capacity will vary depending on the product configuration and usage, including but not limited to: product model, applications running, power management settings, and product features.The battery warranty does not cover natural deterioration of battery capacity. Your battery is only warranted from defects in materials or workmanship resulting in failure.To determine if your battery has had a warranted failure you may be required to run an HP diagnostic.
Solution
Select one of the methods below to check the status of an HP notebook PC battery to determine if needs to be replaced:
Method 1: Check the battery status using the HP Battery Check . (For HP notebook PCs manufactured in 2005 or later)
Method 2: Check the battery status manually (For HP notebook PCS not supported by the HP Battery Check or manufactured before 2005)
Also see Method 3: Reduce the operating temperature and increase the battery life for information the best conditions for charging your battery.
Method 1: Check the battery status using the HP Battery Check
Use the following steps to download, install and use the HP Battery Check on all notebooks manufactured after 2004.
For more information about using the HP Battery test, including a list of notebook PCs that are supported, see HP Notebook PCs - HP Battery Check Frequently Asked Questions .
Download and install the HP Battery Check
Download the HP Battery Check SoftPaq at the following location:
HP Battery Check (SP32299)
Click Run.
If a security warning displays, click Run.
Click Next.
Click next to the I accept the terms of the license agreement, then click Next.
Click Next again.
NOTE: If a This system is not supported by the HP Battery Check tool warning screen displays, the notebook model is not supported by the HP Battery Check and you should use Method 2: Check the battery status manually .
Test the battery using the HP Battery Check
Insert the AC power adapter into the notebook PC and plug directly into a wall outlet.
Click Start, All Programs, then click Hewlett-Packard, HP Battery Check.
The results of the Battery test will be presented immediately. Detailed instructions are provided with the results. One of the following results will appear in the Battery Health section:
Good - the battery is in working order.
Replace - one or more of the cells can no longer accept a charge or the storage capacity is "Low" and the battery should to be replaced. Instructions stating where to purchase a replacement battery or if the battery is covered by HP under warranty will display.
Invalid - either the AC adapter is not connected, more than one battery is installed or the battery is not installed correctly. Please follow the instructions in the Battery Check to correct the condition.
NOTE: If the Battery Check detects a failure, you will be prompted to contact HP support to discuss the warranty service options available to you. A WARRANTY ID and SAT ID is provided to you by the Battery Check. This information will assist the HP support representative with your replacement options.
Method 2: Check the battery status manually
Use the following steps to check the battery status on a notebook, manufactured in 2004 or earlier, while it is not in use.
To accurately measure the condition of the battery, the PC cannot be used during this test. This method will Test the battery by completely charging the battery then will determine how long it takes to discharge the battery. This test is done while the PC is operating in the Safe Mode and not being used for any other action.
This test will require 1-3 hours depending on condition of the notebook PC. The PC cannot be used while you perform the following steps. Completing all the following steps will also calibrate the battery so that the power meter reading are accurate.
Connect the AC adapter and allow the notebook to charge until the battery is charged to 99% - 100% of capacity.
To determine the percentage of battery power, with the notebook operating normally, right-click on the power icon in the system tray, and select Open power meter. The Power Status is displayed.
Shut down the notebook PC when the battery has charged to capacity.
With the notebook turned off, connect the notebook PC to the AC power adapter that is plugged into a working wall outlet.
Press and release the Power Button to start the computer.
Press the F8 key several times when the HP Logo displays.
When the Windows Advanced Startup Menu displays, select the Startup in Safe Mode option.
Notice and record the current time as the Test Start Time with a fully charged battery.
Remove the AC power adapter cable from the notebook PC.
Allow the battery to discharge completely until the notebook PC turns off.
Notice and record the Completely Discharged Time.
Subtract the Discharged Time from the Start Time to calculate the Elapsed time.
Record the time for future comparison or to provide to an HP support specialist if you suspect the battery is defective.
NOTE: As with all batteries, the maximum capacity of this battery will decrease with time or use. Loss of battery capacity will vary depending on the product configuration and usage, including but not limited to: product model, applications running, power management settings, and product features.The battery warranty does not cover natural deterioration of battery capacity. Your battery is only warranted from defects in materials or workmanship resulting in failure.To determine if your battery has had a warranted failure you may be required to run an HP diagnostic.
Method 3: Reduce the operating temperature and increase battery life
The battery in your notebook PC is designed to provide the necessary amount of energy for the processor while maintaining HP high safety standards. As a result, the battery may not charge or may stop providing power to the notebook when the battery temperature exceeds the specified, design safety level.
If the battery life appears shorter than normal, the battery stops charging before it is 99%-100% full and the battery appears warmer than usual, the battery has most likely reached its designed "no charge" safety state. The battery will no longer charge until the temperature condition is corrected.
Try one of the following methods to correct the battery temperature:
When charging the battery, do not use applications that require large amounts of system resources such as graphic or memory intensive applications, heavy and extended hard drive usage.
Turn off your notebook and remove the battery to allow it to return to a safe operating temperature.
Make sure the notebook PC is operating on a hard surface. Using the Notebook PC on a bed or sofa may block the vents causing the notebook PC to heat up and shut down.
By taking these steps, the battery will return to its normal operating temperature range and continue to charge and discharge as designed.
Power Management for Notebooks Running Windows 98, ME, XP and 2000
Power Management for Notebooks Running Windows 98, ME, XP and 2000
___________________________________________________
This document applies to all Pavilion and Presario notebooks using Windows 98, ME, XP and 2000.
This document explains the following main topics:
Understanding Power Management
Using Windows Power Options Properties
Understanding power management
Power management lets you reduce your Notebook power consumption. Your Notebook has two power management modes:
Hibernation is an energy-saving feature and safeguard that saves information to the hard drive, then turns off your Notebook. When you resume from Hibernation, your information returns to the screen where you were previously working. Your Notebook hibernates when the Power button is pressed, when the battery has little power left, or when your Notebook (operating on battery power) is in Sleep mode for more than one hour.
Sleep, also called Standby, is an energy-saving feature that reduces power to system components that are not being used. When Sleep is initiated, your information is saved in Random Access Memory (RAM), and the screen is cleared. Your Notebook is still on, but the display is blank. When you resume from Suspend, your information returns to the screen where you were previously working.
Automatically put your notebook into hibernation
Windows can automatically put your computer into Hibernate mode after a specified period of inactivity. Or Windows can detect when your batteries are running low, and then automatically put your computer in Hibernate mode to save your work before the battery fails.
NOTE: Using Power Options in Control Panel, you can adjust any power management option that your notebook's unique hardware configuration supports. Because these options may vary widely from computer to computer, the options described may differ from what you see. Power Options automatically detects what is available on your computer and shows you only the options that you can control.
To automatically put your computer into hibernation:
In Category view, click Start, click Control Panel, click Performance and Maintenance, and then click Power Options.
In Classic view, click Start, click Control Panel, and then click the Power Options icon.
Click the Hibernate tab, select the Enable hibernate support check box, and then click Apply.
Figure 1: Enable hibernation check box
Click the Power Schemes tab, and then select a time period in System hibernates. Your computer hibernates after it has been idle for the specified amount of time.
Manually put your notebook into hibernation
This feature is available only on notebooks with the Windows XP operating system installed.
In Category view, click Start, click Control Panel, click Performance and Maintenance, and then click Power Options.
In Classic view, click Start, click Control Panel, and then click the Power Options icon.
Click the Hibernate tab, and then select the Enable hibernate support check box.
NOTE: If the Hibernate tab is not available, your computer does not support this feature.
Click OK to close the Power Options dialog box.
Click Start, and then click Turn Off Computer. In the Turn off computer dialog box, hold down the Shift key. The Stand By button will change to Hibernate. Click Hibernate.
___________________________________________________
This document applies to all Pavilion and Presario notebooks using Windows 98, ME, XP and 2000.
This document explains the following main topics:
Understanding Power Management
Using Windows Power Options Properties
Understanding power management
Power management lets you reduce your Notebook power consumption. Your Notebook has two power management modes:
Hibernation is an energy-saving feature and safeguard that saves information to the hard drive, then turns off your Notebook. When you resume from Hibernation, your information returns to the screen where you were previously working. Your Notebook hibernates when the Power button is pressed, when the battery has little power left, or when your Notebook (operating on battery power) is in Sleep mode for more than one hour.
Sleep, also called Standby, is an energy-saving feature that reduces power to system components that are not being used. When Sleep is initiated, your information is saved in Random Access Memory (RAM), and the screen is cleared. Your Notebook is still on, but the display is blank. When you resume from Suspend, your information returns to the screen where you were previously working.
Automatically put your notebook into hibernation
Windows can automatically put your computer into Hibernate mode after a specified period of inactivity. Or Windows can detect when your batteries are running low, and then automatically put your computer in Hibernate mode to save your work before the battery fails.
NOTE: Using Power Options in Control Panel, you can adjust any power management option that your notebook's unique hardware configuration supports. Because these options may vary widely from computer to computer, the options described may differ from what you see. Power Options automatically detects what is available on your computer and shows you only the options that you can control.
To automatically put your computer into hibernation:
In Category view, click Start, click Control Panel, click Performance and Maintenance, and then click Power Options.
In Classic view, click Start, click Control Panel, and then click the Power Options icon.
Click the Hibernate tab, select the Enable hibernate support check box, and then click Apply.
Figure 1: Enable hibernation check box
Click the Power Schemes tab, and then select a time period in System hibernates. Your computer hibernates after it has been idle for the specified amount of time.
Manually put your notebook into hibernation
This feature is available only on notebooks with the Windows XP operating system installed.
In Category view, click Start, click Control Panel, click Performance and Maintenance, and then click Power Options.
In Classic view, click Start, click Control Panel, and then click the Power Options icon.
Click the Hibernate tab, and then select the Enable hibernate support check box.
NOTE: If the Hibernate tab is not available, your computer does not support this feature.
Click OK to close the Power Options dialog box.
Click Start, and then click Turn Off Computer. In the Turn off computer dialog box, hold down the Shift key. The Stand By button will change to Hibernate. Click Hibernate.
Battery Does not Power Notebook or Hold a Charge
Battery Does not Power Notebook or Hold a Charge
Security level: Public
___________________________________________________
In this document:
Troubleshoot the power supply
Troubleshoot the System Board
Troubleshoot the battery
Understanding problems with a notebook battery
The notebook battery may have a defect if it will not power on the notebook and if it will not hold a charge. The battery indicator light on the notebook either does not light or always blinks orange. The notebook operates correctly when connected to the AC adapter.
A battery that will not charge may be the result of an AC adapter failure, a system board failure, or a battery failure. Perform the steps below to diagnose the failure.
Troubleshoot the power supply
To verify that the AC power supply is functioning properly, follow the steps below.
Plug the AC adapter directly into a functioning wall outlet, and plug connector into the computer. Do not plug into a power strip, surge protector or secondary power source.
Verify the following operation and take the appropriate action:
That all power cord connections are secure.
If the AC adapter connection to the notebook is loose, the connector may be damaged and require repair. Contact HP service and support for further assistance.
That the power button or power LED is lit when the computer is on.
That an LED on the AC power supply adapter is lit when plugged into an AC wall outlet (not available on all AC power supply adapters).
That the AC power supply adapter is the correct type.
Different notebook models require different AC power supply adapters. You will need to know the Product Number of your notebook to determine the Part Number of the replacement part. Click Start > HP Help & Support to view the product name, product number, and serial number that you'll need to have to speak with HP Customer Service.
View the See Also section for information about locating HP Help & Support in your operating system.
Troubleshoot the System Board
If you've verified that the AC power functions properly, troubleshoot the PC's system board by following the steps below.
Remove the battery, and keep the notebook connected to AC power.
Press and release the Power button to start the computer.
If the notebook PC powers on, then the AC adapter and system board are functioning properly. go to Troubleshoot the battery .
If the Power LED is off, then the AC power adapter needs to be replaced. Contact HP Service and Support for further assistance.
If the power LED is on, but the notebook PC does not power on, then the notebook PC needs to be repaired. Contact HP Service and Support for further assistance.
Shut down Windows by selecting Shut Down from the Start Menu.
Troubleshoot the battery
If you have verified the AC power supply and system board are functioning correctly, troubleshoot the battery by following the steps below.
Insert the battery into the battery compartment on the bottom of the notebook PC.
Connect the AC power supply and allow the battery to charge for 15 to 30 minutes.
NOTE: The Battery Charging light should be on while the battery is charging. If it is not on, check the AC power adapter connection to the notebook PC.
Unplug the AC power adapter cord from the notebook PC.
Press and release the Power button to start the computer using only the battery as the power source.
If the PC does not power on, then the battery needs to be replaced. Contact HP service and support for further assistance.
If the notebook PC does power on, the battery is functioning properly.
NOTE: If you have purchased a second battery for your notebook PC or you have access to an identical battery, you can also check the battery by inserting the second battery into the PC and performing the Troubleshoot the battery steps again.
Security level: Public
___________________________________________________
In this document:
Troubleshoot the power supply
Troubleshoot the System Board
Troubleshoot the battery
Understanding problems with a notebook battery
The notebook battery may have a defect if it will not power on the notebook and if it will not hold a charge. The battery indicator light on the notebook either does not light or always blinks orange. The notebook operates correctly when connected to the AC adapter.
A battery that will not charge may be the result of an AC adapter failure, a system board failure, or a battery failure. Perform the steps below to diagnose the failure.
Troubleshoot the power supply
To verify that the AC power supply is functioning properly, follow the steps below.
Plug the AC adapter directly into a functioning wall outlet, and plug connector into the computer. Do not plug into a power strip, surge protector or secondary power source.
Verify the following operation and take the appropriate action:
That all power cord connections are secure.
If the AC adapter connection to the notebook is loose, the connector may be damaged and require repair. Contact HP service and support for further assistance.
That the power button or power LED is lit when the computer is on.
That an LED on the AC power supply adapter is lit when plugged into an AC wall outlet (not available on all AC power supply adapters).
That the AC power supply adapter is the correct type.
Different notebook models require different AC power supply adapters. You will need to know the Product Number of your notebook to determine the Part Number of the replacement part. Click Start > HP Help & Support to view the product name, product number, and serial number that you'll need to have to speak with HP Customer Service.
View the See Also section for information about locating HP Help & Support in your operating system.
Troubleshoot the System Board
If you've verified that the AC power functions properly, troubleshoot the PC's system board by following the steps below.
Remove the battery, and keep the notebook connected to AC power.
Press and release the Power button to start the computer.
If the notebook PC powers on, then the AC adapter and system board are functioning properly. go to Troubleshoot the battery .
If the Power LED is off, then the AC power adapter needs to be replaced. Contact HP Service and Support for further assistance.
If the power LED is on, but the notebook PC does not power on, then the notebook PC needs to be repaired. Contact HP Service and Support for further assistance.
Shut down Windows by selecting Shut Down from the Start Menu.
Troubleshoot the battery
If you have verified the AC power supply and system board are functioning correctly, troubleshoot the battery by following the steps below.
Insert the battery into the battery compartment on the bottom of the notebook PC.
Connect the AC power supply and allow the battery to charge for 15 to 30 minutes.
NOTE: The Battery Charging light should be on while the battery is charging. If it is not on, check the AC power adapter connection to the notebook PC.
Unplug the AC power adapter cord from the notebook PC.
Press and release the Power button to start the computer using only the battery as the power source.
If the PC does not power on, then the battery needs to be replaced. Contact HP service and support for further assistance.
If the notebook PC does power on, the battery is functioning properly.
NOTE: If you have purchased a second battery for your notebook PC or you have access to an identical battery, you can also check the battery by inserting the second battery into the PC and performing the Troubleshoot the battery steps again.
Notebook PC Battery Discharge Time May Be Shorter Than Expected in Windows Vista
Notebook PC Battery Discharge Time May Be Shorter Than Expected in Windows Vista
___________________________________________________
In this document:
Understanding Bluetooth issues in Windows Vista
Download and Install Windows Updates
Re-enable Selective Suspend
This document pertains to Notebook PCs with Windows Vista.
Understanding Bluetooth issues in Windows Vista
An issue with Microsoft Windows Vista Bluetooth implementation could cause Bluetooth malfunction and/or system instability (hang/blue screen). In order to resolve the issue the Bluetooth "Selective Suspend" option in the driver was disabled. The disabling of selective suspend may cause a loss of up to 30 min of battery life.
Follow the steps below to download patches and re-enable Selective Suspend to improve battery life.
Download and Install Windows Updates
To resolve this issue, download and install QFE 929577 from Windows Update and then re-enable selective suspend in the Bluetooth driver to improve battery life.
Perform the following steps to find and install updated software and hardware drivers for your PC with Windows Vista:
Create a system restore point to back up your system before starting. If you do not know how to create a system restore point, see Related links for more information.
If you are not already connected to the Internet, connect now.
Click Start, and type Windows Update in the Search field. Select Windows Update as soon as it becomes available.
In the Windows Update page, click Check for updates in the left pane.
When the required update appears, select it and click on Install updates button. Some updates may require you to restart your computer.
Re-enable Selective Suspend
To re-enable Selective Suspend, perform the following:
Click Start, type Device Manager in the search field and press Enter.
Select Device Manager.
Click the + sign next to Bluetooth Radios.
Double click HP Integrated Bluetooth module.
On the Power Management tab, click the box next to Allow the computer to turn off this device to save power.
Click OK.
Close Device Manager.
NOTE: If Bluetooth is not in use, turning it off through Wireless Assistant will also avoid the battery life loss (even if the QFE has not been installed).
___________________________________________________
In this document:
Understanding Bluetooth issues in Windows Vista
Download and Install Windows Updates
Re-enable Selective Suspend
This document pertains to Notebook PCs with Windows Vista.
Understanding Bluetooth issues in Windows Vista
An issue with Microsoft Windows Vista Bluetooth implementation could cause Bluetooth malfunction and/or system instability (hang/blue screen). In order to resolve the issue the Bluetooth "Selective Suspend" option in the driver was disabled. The disabling of selective suspend may cause a loss of up to 30 min of battery life.
Follow the steps below to download patches and re-enable Selective Suspend to improve battery life.
Download and Install Windows Updates
To resolve this issue, download and install QFE 929577 from Windows Update and then re-enable selective suspend in the Bluetooth driver to improve battery life.
Perform the following steps to find and install updated software and hardware drivers for your PC with Windows Vista:
Create a system restore point to back up your system before starting. If you do not know how to create a system restore point, see Related links for more information.
If you are not already connected to the Internet, connect now.
Click Start, and type Windows Update in the Search field. Select Windows Update as soon as it becomes available.
In the Windows Update page, click Check for updates in the left pane.
When the required update appears, select it and click on Install updates button. Some updates may require you to restart your computer.
Re-enable Selective Suspend
To re-enable Selective Suspend, perform the following:
Click Start, type Device Manager in the search field and press Enter.
Select Device Manager.
Click the + sign next to Bluetooth Radios.
Double click HP Integrated Bluetooth module.
On the Power Management tab, click the box next to Allow the computer to turn off this device to save power.
Click OK.
Close Device Manager.
NOTE: If Bluetooth is not in use, turning it off through Wireless Assistant will also avoid the battery life loss (even if the QFE has not been installed).
Subscribe to:
Posts (Atom)